汽车钢B30APV1500

电工钢硅钢片2 供货形式6.2.1 产品以卷供货，简称钢卷。钢卷的重量应符合订货要求，卷重一般3～10 吨，特殊卷重应在订货时协商并在合同中注明。6.2.2 钢卷通常以切边状态交货。用户有特殊要求时，应在订货时协商并在合同中注明。6.2.3 钢卷内径应在 500mm～520mm 范围内，钢卷内径为 508mm。6.2.4 钢卷应由同一宽度的钢带连续、湖北荆门附近紧密卷绕，卷的侧面应尽量平直，自重下不塌卷。6.3 交货状态钢带以终退火并两面涂敷绝缘涂层的状态交货。6.4 表面质量6.4.1 钢带表面应光滑清洁，无油脂，无锈渍，无影响使用的缺陷。6.4.2 钢带表面允许存在不影响材料正常使用的在厚度偏差允许范围内的基板缺欠、湖北荆门本地绝缘涂层缺欠，如轻微划伤、湖北荆门本地色差、湖北荆门本地辊印、湖北荆门本地斑纹等缺欠。

电工钢硅钢片：本文件的符号和相应的说明见表1。表 1 符号和说明符号 单位 说明P W/kg 比总损耗，通常称为铁损P1.5/50 W/kg 磁极化强度在1.5T、湖北荆门附近频率在50Hz下测得的比总损耗P1 W/kg 横向试样的比总损耗值P1.5/50 P2 W/kg 纵向试样的比总损耗值P1.5/50 T1.5/50 ％ 比总损耗P1.5/50的各向异性H A/m 磁场强度J T 磁极化强度J1000 T 磁场强度峰值为1000A/m下测得的磁极化强度峰值J2500 T 磁场强度峰值为2500A/m下测得的磁极化强度峰值J5000 T 磁场强度峰值为5000A/m下测得的磁极化强度峰值J10000 T 磁场强度峰值为10000A/m下测得的磁极化强度峰值μ0 H/m 真空中的磁导率取4?×10-7 B T 磁感应强度，B＝μ0H＋JReL MPa 下屈服强度Rm MPa 抗拉强度A ％ 断后伸长率C Ω·cm2/面或Ω·mm2/面 表面绝缘电阻系数RA Ω·cm2/片或Ω·mm2/片 层间电阻系数

电工钢硅钢片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Since it is a functional material, its performance testing also revolves around "function". These indicators are often mentioned in trade and processing processes, and a brief understanding can help everyone better carry out their work. The performance testing of electrical steel mainly includes the following aspects: magnetic inspection, stacking coefficient inspection, coating adhesion inspection, repeated bending inspection, size and shape surface inspection, and conventional mechanical property inspection. In addition to the types of products listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, which are used as intermediate and intermediate grade High frequency motors and transformers, as well as pulse transformers, etc； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding. Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength. Magnetic induction strength is the number of magnetic lines passing through a unit cross-sectional area of the iron core, also known as magnetic flux density. It represents the material‘s magnetization ability, measured in T. The magnetic induction strength of electrical steel plates is high, and the excitation current (also known as no-load current) of the iron core is reduced. Copper and iron losses are also reduced, which can save electrical energy. When the power of the motor and transformer remains constant, the magnetic induction intensity is high, and the design Bm can be increased. The cross-sectional area of the iron core can be reduced, which reduces the volume and weight of the iron core, and saves the amount of electrical steel plates, wires, insulation materials, and structural materials used. This can reduce the total loss and manufacturing cost of the motor and transformer, and is beneficial for the manufacturing, installation, and transportation of large transformers and motors. The main requirements for the performance of silicon steel are: 1. Low iron loss is the most important indicator of the quality of silicon steel sheets. Various countries classify grades based on iron loss values, with the lower the iron loss, the higher the grade. 2. Under strong magnetic fields, the magnetic induction intensity (magnetic induction) is high, which reduces the volume and weight of the iron core of the motor and transformer, saving silicon steel sheets, copper wires, and insulation materials. 3. The surface is smooth, flat, and the thickness is uniform, which can improve the filling coefficient of the iron core. 4. Good lamination performance is more important for manufacturing micro and small electric motors. 5. The adhesion and weldability of the surface insulation film are good, which can prevent corrosion and improve the punching performan