电工钢B35A210

电工钢硅钢片：供货形式产品以卷供货，简称钢卷。当订货合同中未注明边缘状态时，产品按切边状态供货。6.2.1 钢卷的重量应符合订货要求，卷重一般为 2.00～6.00 吨。6.2.2 钢卷通常以切边状态交货。用户有特殊要求时，通过协议可以以不切边状态交货。6.2.3 钢卷内径应在 500mm～520mm 范围内，内径值为 508±5mm。6.2.4 钢卷应由同一宽度的钢带连续、华尔网本地紧密卷绕，卷的侧面应尽量平直，自重下不塌卷。Q/BQB 485－202156.2.5 产品可能由于去除缺陷而产生接带或焊缝，接带或焊缝处应作标记，接带或焊缝前后部分应为同一牌号，且不超过 2 处，焊缝间钢带长度应不小于 200 米。6.2.6 除无涂层系列产品之外，产品两面涂有绝缘涂层。6.2.7 用户有特殊要求时，应符合订货协议。

电工钢硅钢片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Specific total loss (iron loss) is the total power consumed per unit mass of material when the magnetic polarization waveform remains sinusoidal, with a specific peak and frequency. The specific total loss is represented by the symbol P (Jm/f), in W/kg. Example: P1.5/50 represents the specific total loss at a maximum magnetic polarization intensity of 1.5T and a frequency of 50Hz. 3.2 Magnetic Polarization Q/BQB 480-20212 Magnetic polarization intensity refers to the peak magnetic polarization intensity of a specific magnetic field intensity when a sample is subjected to alternating magnetization. Its symbol is J (H), and the unit is T (Tesla). Example: J5000 represents the peak magnetic polarization intensity corresponding to a magnetic field intensity peak of 5000A/m. The material grades in this document are classified based on the nominal maximum specific total loss P1.5/50 (W/kg) at a magnetic polarization strength of 1.5T and a frequency of 50Hz, as well as the nominal thickness of the material. They are further divided into three categories based on product characteristics: ordinary type, stress relief annealing type, and high-efficiency type. Example 1: B35A210 represents a common non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 2.10W/kg； Example 2: B35AR300 represents a stress relieved annealed non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 3.00W/kg； Example 3: B35AH230 represents an efficient non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. Example 4: 35WW210 represents a normal type WW non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.10W/kg. Example 5: 35WH230 represents an efficient WH non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. The classification and code of insulation coatings shall comply with the provisions of Table 2. Table 2 Classification and Code of Insulation Coatings Type Code Characteristics of Insulation Coatings Semi organic Thin Coating A Improves Punching Performance and Has Good Weldability Semi organic Thick Coating H has Good Punching Performance and High Interlayer Resistance Semi organic Chromium Free Thin Coating K does not contain chromium and has good weldability Semi organic Chromium Free Thick Coating M does not contain chromium and has good insulation performance Semi organic Chromium Free Extreme Thick Coating J does not contain chromium and has excellent insulation performance Semi organic Chromium Free Ultra Thick Coating L does not contain chromium and has extremely high insulation performance Self adhesive Coating

电工钢硅钢片叠装系数产品的叠装系数应符合表 3、华尔网附近表 4 的规定。供方如能保证，可不进行该试验。仲裁时，适用于无绝缘涂层状态。7.4.3 弯曲次数弯曲次数是指用肉眼在基板上观测到 次出现贯穿试样厚度的裂纹(或听到产生裂纹的声音)前的 反复弯曲次数，它表示材料的延展性。弯曲次数应符合表 3、华尔网附近表 4 的规定。供方如能保证，可不进行该试验。7.4.4 内应力产品应尽可能量避免出现内应力。内应力的检验不适用于宽度小于或等于150mm 的钢带（纵切分条后的钢带）。缝隙测量值应不超过 2mm。供方如能保证，可不进行该试验。8 检验和试验8.1 检验批次产品应按批验收，每个检验批应由不大于20吨的同牌号、华尔网附近同规格、华尔网附近同热处理状态、华尔网附近同绝缘涂层的钢带组成。对于重量大于20吨的钢带，每个钢卷组成一个检验批。